找回密码注册

QQ登录

只需一步,快速开始

 
 
 
 
楼主: 叨叨催人老

[量产刀] 长篇评书:《五十名刀记》

[复制链接]

该用户从未签到

发表于 2012-7-2 14:12 | 显示全部楼层
很贼的刀
  • TA的每日心情

    2016-2-22 09:44
  • 签到天数: 126 天

    [LV.7]常住居民III

    发表于 2012-7-2 21:17 | 显示全部楼层
    此刀不是我喜欢的类型,继续保持关注。
    照片 060_conew1.jpg 照片 054_conew1.jpg 照片 066_conew1.jpg
  • TA的每日心情

    2013-6-25 18:31
  • 签到天数: 1 天

    [LV.1]初来乍到

     楼主| 发表于 2012-7-3 18:07 | 显示全部楼层
    本帖最后由 叨叨催人老 于 2012-7-5 20:50 编辑

    第十五把  Ontario SP 42

        我其实是先买的SP 42,然后才是SP 10。
        42也不贵,钢材与10不同,刀型属于我个人标准里的“完形”。这个刀型是有来历的,来看SP系列的设计师Dan Maragni 写给他朋友(也是一位刀匠)的一封信:
        Hi Bill,

    Here is some information about the Gen II Spec Plus line that are being made at Ontario. I was given complete control over the material, heat treatment and manufacturing process, so I took my 18 years of factory experience and, remembering all the failures I had seen in knives over that period, eliminated any processes that might damage the knife.

    1. Material- American made 5160 and not some unknown import of indifferent quality supplied by a large steel retailer. This stuff is made by WCI in the US and I had micros done so I could examine the material and it is very nice. I like 5160 because it is quite a bit tougher than the higher carbon steels (such as 1095) and is much more compatible to industrial style heat treatment. I also found the cutting ability comparable to higher carbon steels in my physical testing, contrary to what one might read in the literature.

    2. Water Jet Cutting- the blade blanks were cut out of the plate using a water jet cutter rather than a laser because I have seen many blades ruined by laser cutting. The laser leaves a heat effected zone around the perimeter of the blank which has a combination of melted steel, hardened steel and hardened and tempered steel which can cause cracking while the blanks are being cut and when heat treated.

    3. Stress Relief- I introduced a vacuum stress relief operation after cutting to eliminate any residual stress that might cause straightening or other problems due mainly to coil memory.

    4. Surface Grind- I had about 0.030" per side ground off to eliminate any possibility of problems from the hot rolled surface. I once had blades made of 5160 from a large steel retailer crack due to cracks in the surface of the material from the hot rolling process."

    5. Heat Treatment- I set the hardening temperatures, soak times, quench, snap temper and temper procedures based on my research/experimentation with this material. I heat treated blades in my shop, tested them and then had metallurgical analysis done of each procedure to document them. I also added the snap temper step to the factory heat treatment. This is an operation that I have never seen done in any other knife factory but one that I have always used in my own knife making and is common in commercial heat treatment plants. What it does is relieves some of the stresses of hardening before the clamp and temper operation and prevents any cracking of the blades while tempering. I also introduced heavy duty tempering racks which results in straighter blades which results in more consistent grinds.

    6. Grind- I supervise the grinding set ups and specify dimensions for the taper and edge thickness which results in functional blade geometries which can be repeated throughout the production.

    7. Laser Imprint- I have seen many blades damaged or destroyed by stamped imprints. When blades are powder coated they must be imprinted deeply and I have seen blades cracked by the imprint or weakened to the point that they crack in heat treatment. These blades are laser engraved which only really effects the powder coat.

    8. Sharpening- I trained the sharpeners at Ontario and they sharpen with two abrasive belts of different grits to refine the edge (the usual factory procedure uses one belt) and then a buff to remove the burr and further refine the edge.

    9. Designs- I tried to design these blades from a strictly functional perspective. The blades are fairly wide and flat ground to maximize cutting ability and are based on traditional designs with various functional aspects exaggerated. The SP-40 blade is based on the European "Alpine" knife, the SP-41 on the Skene Dhu and the SP 42 and 43 based on a variety of dirks.

    Regards,
    Dan

        信里全面地介绍了SP系列的选材、切割、热处理、打磨和设计思想,可以看出SP系列采用了部分高端刀具才有的制造工序,这才是其性价比高的真正原因。
        限于本人拙劣的英文水平,翻译工作还是交给有心有力的刀友去做吧,尤其是对SP感兴趣的刀友--我担保你将越翻译越欢喜。
    sp 42.jpg
  • TA的每日心情
    开心
    2014-7-14 08:04
  • 签到天数: 96 天

    [LV.6]常住居民II

    发表于 2012-7-3 18:58 | 显示全部楼层
    哈,兄弟的SP10在我手中。。。。
  • TA的每日心情

    2016-2-22 09:44
  • 签到天数: 126 天

    [LV.7]常住居民III

    发表于 2012-7-3 19:23 | 显示全部楼层
    中规中矩的刀刀,请继续。
  • TA的每日心情

    2013-6-25 18:31
  • 签到天数: 1 天

    [LV.1]初来乍到

     楼主| 发表于 2012-7-3 19:25 | 显示全部楼层
    本帖最后由 叨叨催人老 于 2012-7-4 09:47 编辑
    哈,兄弟的SP10在我手中。。。。
    刃少点 发表于 2012-7-3 18:58
    哈哈 翻译翻译这封信吧 我保证你越翻译越开心
  • TA的每日心情
    郁闷
    2013-10-5 23:16
  • 签到天数: 1 天

    [LV.1]初来乍到

    发表于 2012-7-3 21:16 | 显示全部楼层
    顶Terzuola
    lz文字不错!
  • TA的每日心情
    郁闷
    2013-10-5 23:16
  • 签到天数: 1 天

    [LV.1]初来乍到

    发表于 2012-7-3 21:17 | 显示全部楼层
    是叫“ 哭虞”吧  之前在贴图区见到 已被下载了? 漂亮!
  • TA的每日心情
    郁闷
    2013-10-5 23:16
  • 签到天数: 1 天

    [LV.1]初来乍到

    发表于 2012-7-3 21:18 | 显示全部楼层
    是叫“ 哭虞”吧  之前在贴图区见到 已被下载了? 漂亮!
  • TA的每日心情

    2013-6-25 18:31
  • 签到天数: 1 天

    [LV.1]初来乍到

     楼主| 发表于 2012-7-4 09:49 | 显示全部楼层
    回楼上:谢欣赏

    是叫“哭虞”,提供下载的不是我。
  • TA的每日心情

    2013-6-25 18:31
  • 签到天数: 1 天

    [LV.1]初来乍到

     楼主| 发表于 2012-7-4 14:52 | 显示全部楼层
    本帖最后由 叨叨催人老 于 2012-7-5 20:47 编辑

    第十六把  Swamp Rat RMDx-LE

        可能是Blackjack给我的负面刺激太深了,以至于潜意识里我一直在寻找机会缝合我那受伤的小心灵。所以当有机会再次面对一把也是凸磨也是极幼开锋也是钢本色也是双护手也是缎面且是限量版且是全龙骨且是SR101钢且是优质热处理的中直时,尽管她的出台费犹在Blackjcak之上,我还是没忍住,摄了。
        这一次我赌对了,这把限量版沼泽鼠即使不算21点,至少也算19点,绝对正点。21点还是贴她丈夫Busse限量版的脑门上吧。
        沼泽鼠的限量版算是半手工刀了,身形窈窕,皮肤细腻,手感和完工度非常好。这把刀我实在挑不出任何毛病,你非要说不如她老头的限量版高阶,那她老头的高价也不是3000多可以拿下的呀!Infi钢我后来也用过,没想象中那么神奇。
        但还是没能留她厮守终生,倒不是因为她是别人的老婆,而是因为我还是太怜香惜玉舍不得操。对于我这种工薪族屌丝来说,泡上个白富美简直是赚足眼球受足罪。让我舍得爆操的直刀的最高价格,不能超过2999元9角9分。
        但我也郑重其事地对她发誓:你是我最后一把中直。从你以后我身边的女人将只有蔡依林和梁咏琪,没有张柏芝和黄圣依。
        对了,哪位知道RMDx是什么的缩写?肉麻短信?

       (这张照片是我拍的实物。)
    沼泽鼠.jpg
  • TA的每日心情
    开心
    2016-6-15 01:19
  • 签到天数: 156 天

    [LV.7]常住居民III

    发表于 2012-7-4 18:03 | 显示全部楼层
    看了这么多,发现LZ的儿子长大后也必是刀友啊!!!
  • TA的每日心情
    开心
    2016-6-15 01:19
  • 签到天数: 156 天

    [LV.7]常住居民III

    发表于 2012-7-4 18:04 | 显示全部楼层
    第十四把 Ontario SP 10

        “没玩过博伊,不算玩过刀”。我觉得这话比那句狗屁的“没玩过沙狗,不算玩过刀”顺耳多了。在陆陆续续错过了几把clip point之后,当看到这把SP 10有现货时,我立即下了单。
            ...
    叨叨催人老 发表于 2012-7-2 14:06

    Ontario SP 10确实在bowie里算是性价比很高的了
  • TA的每日心情

    2013-6-25 18:31
  • 签到天数: 1 天

    [LV.1]初来乍到

     楼主| 发表于 2012-7-4 19:37 | 显示全部楼层
    看了这么多,发现LZ的儿子长大后也必是刀友啊!!!
    辰墨 发表于 2012-7-4 18:03
    那是必须的 哈哈

    该用户从未签到

    发表于 2012-7-4 21:49 | 显示全部楼层
    又有更新了。。。安大略sp10刚好兄弟手里玩过。。。。嫌短了点
  • TA的每日心情
    开心
    2013-8-6 00:33
  • 签到天数: 1 天

    [LV.1]初来乍到

    发表于 2012-7-4 22:31 | 显示全部楼层
    这把Swamp Rat的柄看着就应该很合手的样子
    不错
  • TA的每日心情

    2013-6-25 18:31
  • 签到天数: 1 天

    [LV.1]初来乍到

     楼主| 发表于 2012-7-5 15:56 | 显示全部楼层
    本帖最后由 叨叨催人老 于 2012-7-5 16:18 编辑

    第十七把 Busse GW

        “上过沼泽鼠,躲不过八喜”,这话是我发明的。那段时间八喜被吹上天了,于是有了GW
        我承认我首先是个外形党,其次是钢材党,最后才是研磨党,总之是个过手党。
           GW的外形非常吸引我,我至今认为它是八喜所有小直中最性感的一款,没有之一。
           GWInfi钢材据说非常牛逼,我试过了,该起白点还是会起白点,中规中矩就是了。
           GW的研磨就令人费解了:看形制显然是注重切割,但偏厚的刀身和偏大的刃角又否定着切割。也许是为了维持八喜品牌强壮耐用的口碑吧。GW的耐用度是没有任何问题的,一把彻头彻尾的爆操小直,户外佳佩。
        不喜欢Busse之处在于:这个价位的刀子竟然要另掏腰包买裤子。这就好比影友买了一支高档镜头回来发现厂家的标准配置里竟然不含遮光罩一样可恶。
        遮光罩不是必需的,但裤子是必需的。
        如果能卸去她的涂装,削尖她的下巴,再套上一条漂亮的裤子,那她真是个完美的小妾……
           比做小妾更悲情的,只能是一夜情了。
    bussegw.jpg
  • TA的每日心情

    2013-6-25 18:31
  • 签到天数: 1 天

    [LV.1]初来乍到

     楼主| 发表于 2012-7-5 16:01 | 显示全部楼层
    又有更新了。。。安大略sp10刚好兄弟手里玩过。。。。嫌短了点
    joycezj53 发表于 2012-7-4 21:49
    没错 所以我最终的大直是tops的末日之刃
  • TA的每日心情
    开心
    2018-12-2 22:33
  • 签到天数: 331 天

    [LV.8]以坛为家I

    发表于 2012-7-5 20:06 | 显示全部楼层
    好刀不少啊
  • TA的每日心情
    开心
    2018-10-19 10:20
  • 签到天数: 436 天

    [LV.9]以坛为家II

    发表于 2012-7-5 20:29 | 显示全部楼层
    文笔很赞,刀子也有了性格了
    您需要登录后才可以回帖 登录 | 注册

    本版积分规则

       
    快速回复 返回顶部 返回列表